Concrete testing guide
How to carry out the 30 most common tests on concrete construction — from cement and aggregates, through fresh concrete at the pump, to strength, non-destructive testing (NDT), durability and load tests. Each test lists the governing standard, the equipment, the step-by-step procedure, the calculation and the acceptance criteria.
Materials (before concreting)
Acceptance tests on cement, aggregates, water and reinforcement before they are used.
| Test | What it tells you | Standard |
|---|---|---|
| Cement — standard consistency and setting time | Finds the water content for a paste of standard consistency, then the initial and final setting times. | IS 4031 (Part 4) — standard consistency |
| Cement — compressive strength (mortar cubes) | Verifies the grade of cement (33, 43 or 53) by crushing standard cement–sand mortar cubes. | IS 4031 (Part 6) |
| Cement — fineness and soundness | Fineness controls the rate of strength gain; soundness checks that the cement will not expand after setting because of free lime or magnesia. | IS 4031 (Part 2) — Blaine air permeability |
| Aggregates — sieve analysis (grading) and fineness modulus | Determines the particle size distribution of fine and coarse aggregate to check compliance with grading limits and to proportion mixes. | IS 2386 (Part 1) — methods |
| Aggregates — specific gravity, water absorption and bulking of sand | Specific gravity and absorption are needed for mix design and for correcting batch water; bulking of moist sand corrects volume batching. | IS 2386 (Part 3) |
| Aggregates — crushing value, impact value, abrasion and shape | Assesses the strength, toughness and wear resistance of coarse aggregate and the proportion of flaky and elongated particles. | IS 2386 (Part 4) — crushing, impact, Los Angeles abrasion |
| Sand — silt content (field test) | Quick site check for clay and silt in fine aggregate, which increases water demand and reduces strength. | IS 2386 (Part 2) — deleterious materials (laboratory) |
| Water for mixing and curing | Checks that mixing water does not contain harmful amounts of acids, alkalis, salts, sugar or organic matter. | IS 456 cl. 5.4 |
| Reinforcement — tensile, bend/rebend and mass tests | Confirms the grade, ductility and mass per metre of high strength deformed (TMT) bars. | IS 1786 — requirements |
Fresh concrete
Tests at the point of placing to control workability, density, air and temperature, and to make strength specimens.
| Test | What it tells you | Standard |
|---|---|---|
| Sampling of fresh concrete | Obtaining a representative sample at the point of discharge for all fresh concrete tests and for making strength specimens. | IS 1199 (Part 1):2018 |
| Slump test (workability) | Measures the consistency of concrete of medium to high workability; the most common site control test. | IS 1199 (Part 2):2018 — consistency of fresh concrete |
| Compacting factor test | Measures workability of low-workability concrete (where the slump test is insensitive) as the degree of compaction achieved by a standard amount of work. | IS 1199 (Part 2):2018 |
| Vee-Bee consistometer and flow table tests | Vee-Bee time measures very stiff mixes (precast, roller-compacted); the flow table measures highly workable concrete. | IS 1199 (Part 2):2018 |
| Self-compacting concrete — slump flow, T500, V-funnel, L-box, J-ring | Characterises filling ability, passing ability and segregation resistance of self-compacting concrete (SCC). | IS 1199 (Part 6):2018 |
| Fresh density, yield, air content and temperature | Density checks batching and yield; air content controls durability of air-entrained concrete; temperature controls workability loss and thermal cracking. | IS 1199 (Part 3):2018 — density |
| Setting time of concrete (penetration resistance) | Determines the initial and final setting times of the concrete itself (affected by admixtures and temperature), useful for planning finishing and cold joints. | IS 1199 (Part 7):2018 |
Hardened concrete — strength tests
Destructive tests on specimens and cores that establish the strength of the concrete supplied or in place.
| Test | What it tells you | Standard |
|---|---|---|
| Compressive strength — cube test | The primary test for acceptance of concrete: 150 mm cubes are made at site, cured and crushed at 7 and 28 days. | IS 1199 (Part 5):2018 — making and curing specimens |
| Flexural strength (modulus of rupture) | Tensile strength in bending — used for pavements (PQC), and to check fcr assumptions. | IS 516 (Part 1/Sec 1):2021 |
| Split tensile strength | Indirect tensile strength of concrete on cylinders — used in design studies and for fibre-reinforced or special concretes. | IS 516 (Part 1/Sec 1):2021 (supersedes IS 5816) |
| Core test (in-situ strength) | Determines the strength of concrete actually in the structure when cube results fail, are missing, or when assessing existing buildings. | IS 516 (Part 4):2018 — sampling, preparing and testing cores |
Non-destructive testing (NDT)
In-situ tests that assess uniformity, quality, cover and defects without damaging the structure.
| Test | What it tells you | Standard |
|---|---|---|
| Rebound hammer test (Schmidt hammer) | Measures surface hardness to assess the uniformity of concrete and, with a site calibration, to estimate compressive strength. | IS 516 (Part 5/Sec 4):2020 (supersedes IS 13311 Part 2) |
| Ultrasonic pulse velocity (UPV) test | Measures the speed of an ultrasonic pulse through concrete to assess homogeneity, voids, honeycombing, cracks and quality grading. | IS 516 (Part 5/Sec 1):2018 with Amendment 1 (supersedes IS 13311 Part 1) |
| Cover meter / rebar locator | Locates reinforcement and measures concrete cover — for durability checks, and to plan cores and fixings. | BS 1881-204 (method) |
| Other NDT methods — GPR, impact echo, pull-out, pull-off, thermography | Specialist methods for mapping reinforcement and voids, measuring thickness, near-surface strength and bond of repairs. | ASTM D6432 — ground penetrating radar |
Durability and corrosion assessment
Tests for permeability, carbonation, chlorides and reinforcement corrosion risk.
| Test | What it tells you | Standard |
|---|---|---|
| Carbonation depth (phenolphthalein test) | Determines how deep the concrete has carbonated. | EN 14630 (method) |
| Half-cell potential (corrosion probability) | Maps the electrochemical potential of reinforcement to locate areas where corrosion is likely to be active. | ASTM C876 |
| Chloride content of hardened concrete | Measures chloride ions, which destroy the passive film on reinforcement and cause pitting corrosion. | IS 14959 (Part 2) — hardened concrete |
| Water permeability and absorption | Measures how easily water penetrates the concrete — a direct indicator of durability and of the quality of curing and compaction. | IS 3085 — permeability of cement mortar and concrete |
| Rapid chloride permeability test (RCPT) | Rates the resistance of concrete to chloride ion penetration from the electrical charge passed through a slice in 6 hours. | ASTM C1202 |
Structural assessment
Tests on the completed member or structure when the quality of the concrete or the work is in doubt.
| Test | What it tells you | Standard |
|---|---|---|
| Load test on a structure or member | Proves the strength and stiffness of a slab, beam or floor when concrete quality or construction is in doubt and other tests are inconclusive. | IS 456 cl. 17.6 |
Evaluate your test results
Cube test acceptance
Evaluates 28-day cube results: test result per sample (mean of 3 cubes, ±15% rule), groups of four non-overlapping consecutive results against the Table 11 mean criterion, individual results, statistics and the number of samples required for the quantity cast.
Clauses IS 456 cl. 15.2, 15.4, 16.1, Table 8Core test evaluation
Converts core crushing loads to core strength, corrects for length/diameter ratio, converts to equivalent cube strength and checks the IS 456 acceptance criterion (average ≥ 85% and each core ≥ 75% of the specified cube strength).
Clauses IS 516 (Part 4), IS 456 cl. 17.4UPV quality grading
Converts UPV transit times to pulse velocity at each test location, grades concrete quality to IS 516 (Part 5/Sec 1), flags doubtful zones, checks whether rebound hammer strength estimates are valid, and estimates crack depth by the indirect method.
Clauses IS 516 (Part 5/Sec 1), IS 516 (Part 5/Sec 4), IS 13311 (Part 1)Rebound hammer analysis
Reduces the rebound numbers of a test area (median, mean, scatter and rejection of an unreliable set) and estimates in-situ strength from a calibration line fitted to paired rebound and core/cube strengths of the same concrete.
Clauses IS 516 (Part 5/Sec 4), EN 12504-2 (data reduction), EN 13791 (calibration)Load test evaluation
Works out the test load (full dead load plus 1.25 × imposed load) and evaluates the measured deflections against the IS 456 criteria: maximum deflection limit 40l²/D, 75% recovery within 24 hours, and 80% recovery on a repeated test.
Clauses IS 456 cl. 17.6Before you test
- Use calibrated equipment (compression machines, gauges and NDT instruments should carry current calibration certificates) and trained technicians.
- Record location, date, time, batch / delivery ticket, weather and specimen identification for every test — results without traceability are of little value.
- The descriptions here summarise the procedures; the current edition of each Indian Standard, with amendments, governs.