Quality assurance & verification
The calculation engine is checked against values tabulated in the codes and their design aids. The same benchmarks run as automated tests on every change. Tabulated values are rounded, so each comparison has a tolerance matching the precision of the source table.
Benchmarks
51
Within tolerance
51
IS 456 — design shear strength τc (MPa)
| Case | Source | Reference | Computed | Difference | Result |
|---|---|---|---|---|---|
| M20, pt = 0.15% | IS 456:2000 Table 19 | 0.2800 | 0.2875 | 0.0075 | OK |
| M20, pt = 0.5% | IS 456:2000 Table 19 | 0.4800 | 0.4785 | -0.0015 | OK |
| M20, pt = 1% | IS 456:2000 Table 19 | 0.6200 | 0.6225 | 0.0025 | OK |
| M20, pt = 2% | IS 456:2000 Table 19 | 0.7900 | 0.7851 | -0.0049 | OK |
| M20, pt = 3% | IS 456:2000 Table 19 | 0.8200 | 0.8214 | 0.0014 | OK |
| M25, pt = 0.25% | IS 456:2000 Table 19 | 0.3600 | 0.3648 | 0.0048 | OK |
| M25, pt = 0.75% | IS 456:2000 Table 19 | 0.5700 | 0.5748 | 0.0048 | OK |
| M25, pt = 1.5% | IS 456:2000 Table 19 | 0.7400 | 0.7423 | 0.0023 | OK |
| M25, pt = 2.5% | IS 456:2000 Table 19 | 0.8800 | 0.8778 | -0.0022 | OK |
| M30, pt = 0.5% | IS 456:2000 Table 19 | 0.5000 | 0.4967 | -0.0033 | OK |
| M30, pt = 1.25% | IS 456:2000 Table 19 | 0.7100 | 0.7134 | 0.0034 | OK |
| M30, pt = 3% | IS 456:2000 Table 19 | 0.9600 | 0.9616 | 0.0016 | OK |
| M40, pt = 1% | IS 456:2000 Table 19 | 0.6800 | 0.6767 | -0.0033 | OK |
| M40, pt = 3% | IS 456:2000 Table 19 | 1.010 | 1.013 | 0.0028 | OK |
IS 456 — limiting depth of neutral axis
| Case | Source | Reference | Computed | Difference | Result |
|---|---|---|---|---|---|
| Fe 415, xu,max/d | IS 456 cl. 38.1 Note | 0.4800 | 0.4791 | -0.0009 | OK |
| Fe 500, xu,max/d | IS 456 cl. 38.1 Note | 0.4600 | 0.4560 | -0.0040 | OK |
IS 456 — limiting moment Mu,lim/(fck b d²)
| Case | Source | Reference | Computed | Difference | Result |
|---|---|---|---|---|---|
| Fe 250 | SP 16 Table C | 0.1480 | 0.1483 | 0.0003 | OK |
| Fe 415 | SP 16 Table C | 0.1380 | 0.1380 | -0.0000 | OK |
| Fe 500 | SP 16 Table C | 0.1330 | 0.1336 | 0.0006 | OK |
IS 456 — stress in compression steel fsc (MPa)
| Case | Source | Reference | Computed | Difference | Result |
|---|---|---|---|---|---|
| Fe 415, d′/d = 0.05 | SP 16 Table F | 355.0 | 355.3 | 0.2650 | OK |
| Fe 415, d′/d = 0.1 | SP 16 Table F | 353.0 | 352.1 | -0.8837 | OK |
| Fe 415, d′/d = 0.15 | SP 16 Table F | 342.0 | 342.7 | 0.6758 | OK |
| Fe 415, d′/d = 0.2 | SP 16 Table F | 329.0 | 329.3 | 0.2510 | OK |
| Fe 500, d′/d = 0.05 | SP 16 Table F | 424.0 | 424.1 | 0.0925 | OK |
| Fe 500, d′/d = 0.1 | SP 16 Table F | 412.0 | 412.1 | 0.0906 | OK |
| Fe 500, d′/d = 0.15 | SP 16 Table F | 395.0 | 395.8 | 0.8263 | OK |
| Fe 500, d′/d = 0.2 | SP 16 Table F | 370.0 | 371.8 | 1.829 | OK |
IS 456 — development length (×φ)
| Case | Source | Reference | Computed | Difference | Result |
|---|---|---|---|---|---|
| M20, Fe 415, tension | SP 16 Table 65 | 47.000 | 47.012 | 0.0117 | OK |
| M20, Fe 415, compression | SP 16 Table 65 | 37.600 | 37.609 | 0.0094 | OK |
| M25, Fe 500, tension | Ld = φ·0.87fy/(4·1.6τbd) | 48.500 | 48.549 | 0.0491 | OK |
IS 456 — compression steel deflection factor kc
| Case | Source | Reference | Computed | Difference | Result |
|---|---|---|---|---|---|
| pc = 1.0% | IS 456 Fig. 5 | 1.250 | 1.250 | 0.0000 | OK |
| pc = 3.0% | IS 456 Fig. 5 | 1.500 | 1.500 | 0.0000 | OK |
IS 800 — design compressive stress fcd, fy = 250 MPa (MPa)
| Case | Source | Reference | Computed | Difference | Result |
|---|---|---|---|---|---|
| Buckling class a, KL/r = 10 | IS 800:2007 Table 9(a) | 227.0 | 227.3 | 0.2727 | OK |
| Buckling class a, KL/r = 100 | IS 800:2007 Table 9(a) | 132.0 | 131.5 | -0.4647 | OK |
| Buckling class c, KL/r = 100 | IS 800:2007 Table 9(c) | 107.0 | 107.0 | 0.0253 | OK |
IS 6403 — bearing capacity factors
| Case | Source | Reference | Computed | Difference | Result |
|---|---|---|---|---|---|
| φ = 0°, Nc | IS 6403:1981 Table 1 | 5.140 | 5.140 | 0.0000 | OK |
| φ = 20°, Nc | IS 6403:1981 Table 1 | 14.830 | 14.835 | 0.0047 | OK |
| φ = 20°, Nq | IS 6403:1981 Table 1 | 6.400 | 6.399 | -0.0006 | OK |
| φ = 20°, Nγ | IS 6403:1981 Table 1 | 5.390 | 5.386 | -0.0037 | OK |
| φ = 30°, Nc | IS 6403:1981 Table 1 | 30.140 | 30.140 | -0.0004 | OK |
| φ = 30°, Nq | IS 6403:1981 Table 1 | 18.400 | 18.401 | 0.0011 | OK |
| φ = 30°, Nγ | IS 6403:1981 Table 1 | 22.400 | 22.402 | 0.0025 | OK |
| φ = 40°, Nc | IS 6403:1981 Table 1 | 75.310 | 75.313 | 0.0031 | OK |
| φ = 40°, Nq | IS 6403:1981 Table 1 | 64.200 | 64.195 | -0.0048 | OK |
| φ = 40°, Nγ | IS 6403:1981 Table 1 | 109.4 | 109.4 | 0.0005 | OK |
IS 1893 — spectral acceleration Sa/g
| Case | Source | Reference | Computed | Difference | Result |
|---|---|---|---|---|---|
| Medium soil, T = 1.0 s | IS 1893 (Part 1):2016 cl. 6.4.2 | 1.360 | 1.360 | 0.0000 | OK |
| Soft soil, T = 2.0 s | IS 1893 (Part 1):2016 cl. 6.4.2 | 0.8350 | 0.8350 | 0.0000 | OK |
Steel sections — plastic modulus Zpz (cm³)
| Case | Source | Reference | Computed | Difference | Result |
|---|---|---|---|---|---|
| ISMB 300 | SP 6(1) / IS 800 Annex steel tables | 651.7 | 653.4 | 1.639 | OK |
| ISMB 400 | SP 6(1) / IS 800 Annex steel tables | 1176.2 | 1177.9 | 1.722 | OK |
| ISMB 500 | SP 6(1) / IS 800 Annex steel tables | 2074.7 | 2078.0 | 3.306 | OK |
| ISMB 600 | SP 6(1) / IS 800 Annex steel tables | 3510.6 | 3516.0 | 5.353 | OK |
Other quality measures
- Every tool is executed with its default inputs in the test suite to make sure it produces finite results without errors.
- Steel section dimensions are checked for consistency against the catalogue area and second moment of area of each section.
- Internal consistency checks: flanged beams reduce to rectangular design when the neutral axis lies in the flange; P–M interaction curves are monotonic.
- Found a discrepancy? Every calculation link encodes its inputs — share the link with the issue so it can be reproduced exactly.