IS 456:2000

Two-way slab design using IS 456 moment coefficients (Tables 26 & 27)

Design of rectangular slabs spanning in two directions for any of the nine edge conditions of Table 26 or simply supported (Table 27): moments, reinforcement in both directions, spacing limits, shear and span/depth deflection check.

References:cl. 24.4cl. 26.3.3cl. 26.5.2.1cl. 23.2.1cl. 40.2.1.1Annex DTable 26Table 27
Design is adequateGoverning: (cl. 23.2.1)
62%max. utilisation
Report details
Factored load wuw_u
12.38 kN/m²
Short span midspan moment Mx+M_x^+
6.73 kN·m/m
Long span midspan moment My+M_y^+
4.75 kN·m/m
Short span bottom steel
Ø10 @ 300 mm
Effective depth (short) dxd_x
125 mm

Design checks 3

CheckClauseDemandLimitUtilisation
G-1.151.6 mm125.0 mm41%OK
40.2.1.10.198 MPa0.439 MPa45%OK
23.2.132.0 52.0 62%OK
Reinforcement schedule (per metre width)
LocationMu (kN·m/m)d (mm)Ast,req (mm²/m)Ast,design (mm²/m)ProvideAst,prov (mm²/m)
Mx^+6.73125126180Ø10 @ 300262
Mx^-8.91125168180Ø10 @ 300262
My^+4.7511597180Ø10 @ 300262
My^-6.34115130180Ø10 @ 300262

Detailed calculation

Loads

2
gsw=25×0.150=3.75 kN/m2g_{sw} = 25 \times 0.150 = 3.75\ \mathrm{kN/m^{2}}
IS 875-1
wu=1.50×(3.75+1.50+3.00)=12.38 kN/m2w_u = 1.50 \times (3.75 + 1.50 + 3.00) = 12.38\ \mathrm{kN/m^{2}}
Table 18

Moment coefficients

3
lylx=5.004.00=1.250\dfrac{l_y}{l_x} = \dfrac{5.00}{4.00} = 1.250

1. Interior panel

Table 26
αx−=0.0450, αx+=0.0340, αy−=0.032, αy+=0.024\alpha_x^- = 0.0450,\ \alpha_x^+ = 0.0340,\ \alpha_y^- = 0.032,\ \alpha_y^+ = 0.024
Table 26

Design moments per metre width

2
M=α wu lx2=α×12.38×4.002M = \alpha\,w_u\,l_x^2 = \alpha \times 12.38 \times 4.00^2
D-1.1
Mx−=8.91, Mx+=6.73, My−=6.34, My+=4.75 kN m/mM_x^- = 8.91,\ M_x^+ = 6.73,\ M_y^- = 6.34,\ M_y^+ = 4.75\ \mathrm{kN\,m/m}

Depth check

1
dreq=Mmax0.1336 fck b=51.6 mm≤dx=125.0 mmd_{req} = \sqrt{\dfrac{M_{max}}{0.1336\,f_{ck}\,b}} = 51.6\ \mathrm{mm} \le d_x = 125.0\ \mathrm{mm}
G-1.1(c)

Reinforcement

5
As,min=0.12%×1000×150=180 mm2/mA_{s,min} = 0.12\% \times 1000 \times 150 = 180\ \mathrm{mm^{2}/m}
26.5.2.1
Mx+: Ast=126→max⁡(Ast,As,min)=180 mm2/m, s=min⁡(1000×78.5180, 300)⇒ϕ10 @ 300M_x^+:\ A_{st} = 126 \to \max(A_{st}, A_{s,min}) = 180\ \mathrm{mm^{2}/m},\ s = \min\left(\tfrac{1000 \times 78.5}{180},\ 300\right) \Rightarrow \phi10\ @\ 300
26.3.3(b)
Mx−: Ast=168→max⁡(Ast,As,min)=180 mm2/m, s=min⁡(1000×78.5180, 300)⇒ϕ10 @ 300M_x^-:\ A_{st} = 168 \to \max(A_{st}, A_{s,min}) = 180\ \mathrm{mm^{2}/m},\ s = \min\left(\tfrac{1000 \times 78.5}{180},\ 300\right) \Rightarrow \phi10\ @\ 300
26.3.3(b)
My+: Ast=97→max⁡(Ast,As,min)=180 mm2/m, s=min⁡(1000×78.5180, 300)⇒ϕ10 @ 300M_y^+:\ A_{st} = 97 \to \max(A_{st}, A_{s,min}) = 180\ \mathrm{mm^{2}/m},\ s = \min\left(\tfrac{1000 \times 78.5}{180},\ 300\right) \Rightarrow \phi10\ @\ 300
26.3.3(b)
My−: Ast=130→max⁡(Ast,As,min)=180 mm2/m, s=min⁡(1000×78.5180, 300)⇒ϕ10 @ 300M_y^-:\ A_{st} = 130 \to \max(A_{st}, A_{s,min}) = 180\ \mathrm{mm^{2}/m},\ s = \min\left(\tfrac{1000 \times 78.5}{180},\ 300\right) \Rightarrow \phi10\ @\ 300
26.3.3(b)

Shear check

2
Vu≈wu lx2=24.75 kN/m,τv=0.198 MPaV_u \approx \dfrac{w_u\,l_x}{2} = 24.75\ \mathrm{kN/m},\quad \tau_v = 0.198\ \mathrm{MPa}
40.1
k τc=1.30×0.338=0.439 MPak\,\tau_c = 1.30 \times 0.338 = 0.439\ \mathrm{MPa}
40.2.1.1

Deflection — span/depth ratio (short span)

3
fs=0.58 fy Ast,reqAst,prov=140.0 MPa,pt=0.209%f_s = 0.58\,f_y\,\dfrac{A_{st,req}}{A_{st,prov}} = 140.0\ \mathrm{MPa},\quad p_t = 0.209\%
Fig. 4
kt=2.000,(ld)allow=26×2.000=52.0k_t = 2.000,\quad \left(\dfrac{l}{d}\right)_{allow} = 26 \times 2.000 = 52.0
23.2.1
lxdx=4000125=32.0\dfrac{l_x}{d_x} = \dfrac{4000}{125} = 32.0
24.1
✓ OK · 62%InputsResults

Scope, assumptions and limitations

  • Bars in the long direction are placed above the short-span bars, so dy = dx − φ.
  • Table 26 is valid for ly/lx ≤ 2; beyond that the slab is designed as one-way.
  • Corner torsion reinforcement (Annex D-1.8) is reported but not detailed.