IS 456:2000

Crack width of a rectangular RC section under service moment (Annex F)

Serviceability check of flexural crack width: elastic cracked section analysis (neutral axis, steel and concrete stresses), average strain with tension stiffening, and the design surface crack width at the soffit between bars and at the corner, compared with the limits of cl. 35.3.2.

References:cl. 35.3.2cl. 43.1Annex B-1.3Annex FTable 21
Design is adequateGoverning: (cl. Table 21)
96%max. utilisation
Report details
Design crack width wcrw_{cr}
0.137 mm
Steel stress (service) fsf_s
179.1 MPa
Neutral axis depth xx
183.6 mm
Average strain εm\varepsilon_m
829 ×10⁻⁶

Design checks 2

CheckClauseDemandLimitUtilisation
35.3.20.137 mm0.300 mm46%OK
Table 218.172 MPa8.500 MPa96%OK
Cross-section
b = 300D = 600NA, x = 184
Crack width vs service moment
05010015020025000.050.10.150.20.250.30.35designMs (kN·m)wcr (mm)
  • wcr
  • limit

Detailed calculation

Elastic cracked section

4
m=2803 σcbc=2803×8.5=10.98m = \dfrac{280}{3\,\sigma_{cbc}} = \dfrac{280}{3 \times 8.5} = 10.98
B-1.3(d), Table 21
d=h−cmin−ϕ/2=550.0 mm,As=4×π4202=1257 mm2d = h - c_{min} - \phi/2 = 550.0\ \mathrm{mm},\quad A_s = 4 \times \tfrac{\pi}{4} 20^2 = 1257\ \mathrm{mm^{2}}
b x22=m As (d−x)⇒x=183.6 mm,z=d−x3=488.8 mm\dfrac{b\,x^2}{2} = m\,A_s\,(d - x) \Rightarrow x = 183.6\ \mathrm{mm},\quad z = d - \dfrac{x}{3} = 488.8\ \mathrm{mm}
B-2
fs=MsAs z=179.1 MPa,fc=2Msb x z=8.17 MPaf_s = \dfrac{M_s}{A_s\,z} = 179.1\ \mathrm{MPa},\quad f_c = \dfrac{2M_s}{b\,x\,z} = 8.17\ \mathrm{MPa}
B-2

Average strain at the tension face

2
ε1=fsEs h−xd−x=1018×10−6\varepsilon_1 = \dfrac{f_s}{E_s}\,\dfrac{h - x}{d - x} = 1018 \times 10^{-6}
Annex F
εm=ε1−b (h−x)(a′−x)3 Es As (d−x)=829×10−6(a′=h)\varepsilon_m = \varepsilon_1 - \dfrac{b\,(h - x)(a' - x)}{3\,E_s\,A_s\,(d - x)} = 829 \times 10^{-6}\quad (a' = h)
Annex F

Design surface crack width

3
acr,mid=(s/2)2+(h−d)2−ϕ/2=50.1 mm(s=67 mm)a_{cr,mid} = \sqrt{(s/2)^2 + (h - d)^2} - \phi/2 = 50.1\ \mathrm{mm}\quad (s = 67\ \mathrm{mm})
Annex F
wcr=3 acr εm1+2 acr−cminh−x=0.119 mm(between bars)w_{cr} = \dfrac{3\,a_{cr}\,\varepsilon_m}{1 + 2\,\dfrac{a_{cr} - c_{min}}{h - x}} = 0.119\ \mathrm{mm}\quad (\text{between bars})
Annex F
acr,corner=60.7 mm⇒wcr=0.137 mm(corner)a_{cr,corner} = 60.7\ \mathrm{mm} \Rightarrow w_{cr} = 0.137\ \mathrm{mm}\quad (\text{corner})
Annex F
✓ OK · 96%InputsResults

Scope, assumptions and limitations

  • Single layer of tension bars, compression steel neglected. Crack width is assessed at the tension face midway between bars and at the bottom corner; the larger value governs.
  • Annex F gives a surface crack width with an acceptable probability of not being exceeded; it is not an exact prediction.