IS 456:2000

Development length and lap length of reinforcement

Design development length Ld of bars in tension and compression, including deformed bar and bundled bar factors, with lap lengths for flexural tension, direct tension and compression, plus a full table for all bar diameters.

References:cl. 26.2.1cl. 26.2.1.1cl. 26.2.1.2cl. 26.2.3cl. 26.2.5.1
Report details
Development length (tension) Ld,tL_{d,t}
777 mm
Development length (compression) Ld,cL_{d,c}
622 mm
Lap length — flexural tension llapl_{lap}
777 mm
Lap length — direct tension
1554 mm
Lap length — compression
622 mm
Development length for M25, Fe 500, full stress (single bars)
φ (mm)Ld tension (mm)Ld tension (×φ)Ld compression (mm)Lap flexural tension (mm)Lap compression (mm)
838948.5311389311
1048648.5389486389
1258348.5467583467
1677748.5622777622
2097148.5777971777
25121448.59711214971
28136048.5108813601088
32155448.5124315541243
36174848.5139917481399
40194248.51554not permittednot permitted

Detailed calculation

Design bond stress

3
τbd=1.40 MPa(plain bars, M25)\tau_{bd} = 1.40\ \mathrm{MPa}\quad (\text{plain bars, M25})
26.2.1.1
τbd,t=1.6×1.40=2.24 MPa(deformed bars)\tau_{bd,t} = 1.6 \times 1.40 = 2.24\ \mathrm{MPa}\quad (\text{deformed bars})
26.2.1.1
τbd,c=1.25×2.24=2.80 MPa(bars in compression)\tau_{bd,c} = 1.25 \times 2.24 = 2.80\ \mathrm{MPa}\quad (\text{bars in compression})
26.2.1.1

Development length

3
σs=0.87 fy×1.00=435.0 MPa\sigma_s = 0.87\,f_y \times 1.00 = 435.0\ \mathrm{MPa}
26.2.1
Ld,t=ϕ σs4 τbd=16×435.04×2.24=777 mm=48.5 ϕL_{d,t} = \dfrac{\phi\,\sigma_s}{4\,\tau_{bd}} = \dfrac{16 \times 435.0}{4 \times 2.24} = 777\ \mathrm{mm} = 48.5\,\phi
26.2.1
Ld,c=16×435.04×2.80=621 mm=38.8 ϕL_{d,c} = \dfrac{16 \times 435.0}{4 \times 2.80} = 621\ \mathrm{mm} = 38.8\,\phi
26.2.1

Lap lengths

3
llap,flex=max⁡(Ld,t, 30ϕ)=max⁡(777, 480)=777 mml_{lap,flex} = \max(L_{d,t},\ 30\phi) = \max(777,\ 480) = 777\ \mathrm{mm}
26.2.5.1(c)
llap,direct=max⁡(2Ld,t, 30ϕ)=max⁡(1554, 480)=1554 mml_{lap,direct} = \max(2L_{d,t},\ 30\phi) = \max(1554,\ 480) = 1554\ \mathrm{mm}
26.2.5.1(c)
llap,c=max⁡(Ld,c, 24ϕ)=max⁡(621, 384)=621 mml_{lap,c} = \max(L_{d,c},\ 24\phi) = \max(621,\ 384) = 621\ \mathrm{mm}
26.2.5.1(d)

Scope, assumptions and limitations

  • Lap splices shall not be used for bars larger than 36 mm; welded or mechanical splices are required (cl. 26.2.5.1(a)).
  • Where lapped bars are in tension and more than 50% are lapped at a section, or the clear cover/spacing is small, increase lap lengths per cl. 26.2.5.1(c).