IS 800:2007

Simply supported steel I-beam — bending, shear, lateral-torsional buckling and deflection

Design of a simply supported rolled I-beam (ISMB/ISHB) under uniformly distributed load: classification, design bending strength for laterally supported and unsupported beams (elastic critical moment Mcr, χLT), shear strength with high-shear interaction, web shear buckling limit and serviceability deflection.

References:cl. 5.6.1cl. 8.2.1.2cl. 8.2.2cl. 8.2.2.1cl. 8.4cl. 9.2Table 2Table 6Annex E
Design is adequateGoverning: (cl. 8.2)
76%max. utilisation
Report details
Design bending strength MdM_d
267.7 kN·m
Design shear strength VdV_d
467.1 kN
Section class
Plastic
Deflection δ\delta
6.2 mm

Design checks 3

CheckClauseDemandLimitUtilisation
8.4135.0 kN467.1 kN29%OK
8.2202.5 kN·m267.7 kN·m76%OK
Table 66.186 mm20.0 mm31%OK

Detailed calculation

Design actions

1
Mu=wuL28=45×6.0028=202.5 kN m,Vu=wuL2=135.0 kNM_u = \dfrac{w_u L^2}{8} = \dfrac{45 \times 6.00^2}{8} = 202.5\ \mathrm{kN\,m},\quad V_u = \dfrac{w_u L}{2} = 135.0\ \mathrm{kN}

Section classification (bending)

2
fy=250 MPa, ε=1.000;btf=4.38⇒Plastic;dtw=38.20⇒Plasticf_y = 250\ \mathrm{MPa},\ \varepsilon = 1.000;\quad \dfrac{b}{t_f} = 4.38\Rightarrow\text{Plastic};\quad \dfrac{d}{t_w} = 38.20\Rightarrow\text{Plastic}
Table 2

Section class: Plastic

Shear strength

2
Vd=Av fy3 γm0=3560×2503×1.10=467.1 kNV_d = \dfrac{A_v\,f_y}{\sqrt{3}\,\gamma_{m0}} = \dfrac{3560 \times 250}{\sqrt{3} \times 1.10} = 467.1\ \mathrm{kN}
8.4.1
dtw=41.3 ≤ 67ε=67.0 (no shear buckling check)\dfrac{d}{t_w} = 41.3\ \le\ 67\varepsilon = 67.0\ (\text{no shear buckling check})
8.2.1.1

Bending strength — laterally supported

2
Md=βb Zp fyγm0=1.000×1177902×2501.10=267.7 kN m≤1.2 Ze fyγm0=279.0 kN mM_d = \dfrac{\beta_b\,Z_p\,f_y}{\gamma_{m0}} = \dfrac{1.000 \times 1177902 \times 250}{1.10} = 267.7\ \mathrm{kN\,m} \le \dfrac{1.2\,Z_e\,f_y}{\gamma_{m0}} = 279.0\ \mathrm{kN\,m}
8.2.1.2

Vu = 135.0 kN ≤ 0.6Vd = 280.3 kN: low shear, no moment reduction.

9.2.1

Deflection (serviceability)

1
δ=5 wsL4384 EIz=6.2 mm,δlim=L300=20.0 mm\delta = \dfrac{5\,w_s L^4}{384\,E I_z} = 6.2\ \mathrm{mm},\quad \delta_{lim} = \dfrac{L}{300} = 20.0\ \mathrm{mm}
5.6.1, Table 6
✓ OK · 76%InputsResults

Scope, assumptions and limitations

  • Mcr is computed with the expression of cl. 8.2.2.1 multiplied by the equivalent uniform moment factor c1 (Annex E, load applied at the shear centre, K = Kw = 1).
  • Shear area Av = h·tw for rolled I-sections bending about the major axis (cl. 8.4.1.1).
  • Slender (Class 4) sections are outside the scope of this tool.