IS 800:2007

Fillet weld design strength

Design strength of fillet welds: throat thickness from the fusion face angle, effective length, long joint reduction, minimum and maximum weld size, and combined normal and shear stress check.

References:cl. 10.5.2cl. 10.5.3cl. 10.5.4cl. 10.5.7cl. 10.5.7.3cl. 10.5.10Table 21Table 22
Design is adequateGoverning: (cl. 10.5.10.1.1)
91%max. utilisation
Report details
Throat thickness ttt_t
4.20 mm
Effective length LeffL_{eff}
276 mm
Strength per mm RwR_w
795.4 N/mm
Weld capacity (shear) PdwP_{dw}
219.5 kN

Design checks 5

CheckClauseDemandLimitUtilisation
Table 216.000 mm5.000 mm83%OK
10.5.8.36.000 mm8.500 mm71%OK
10.5.4.1138.0 mm24.0 mm17%OK
10.5.7172.5 MPa189.4 MPa91%OK
10.5.10.1.1298.8 MPa328.0 MPa91%OK

Detailed calculation

Weld geometry

3
tt=K s=0.7×6=4.20 mmt_t = K\,s = 0.7 \times 6 = 4.20\ \mathrm{mm}
10.5.3.2, Table 22
Leff=Lw−2s×nruns=300−2×6×2=276 mmL_{eff} = L_w - 2s \times n_{runs} = 300 - 2 \times 6 \times 2 = 276\ \mathrm{mm}
10.5.4.1
smin=5 mm (thicker part 12 mm),smax=t−1.5=8.5 mms_{min} = 5\ \mathrm{mm}\ (\text{thicker part } 12\ \mathrm{mm}),\quad s_{max} = t - 1.5 = 8.5\ \mathrm{mm}
10.5.2.3, Table 21, 10.5.8.3

Design strength

3
fwd=fu3 γmw=4103×1.25=189.4 MPaf_{wd} = \dfrac{f_u}{\sqrt{3}\,\gamma_{mw}} = \dfrac{410}{\sqrt{3} \times 1.25} = 189.4\ \mathrm{MPa}
10.5.7.1.1
Rw=fwd tt βlw=795.4 N/mmR_w = f_{wd}\,t_t\,\beta_{lw} = 795.4\ \mathrm{N/mm}
10.5.7
Pdw=Rw Leff=219.5 kNP_{dw} = R_w\,L_{eff} = 219.5\ \mathrm{kN}
10.5.7

Stress check

2
q=VttLeff=172.5 MPa,fa=NttLeff=0.0 MPaq = \dfrac{V}{t_t L_{eff}} = 172.5\ \mathrm{MPa},\quad f_a = \dfrac{N}{t_t L_{eff}} = 0.0\ \mathrm{MPa}
fe=fa2+3q2=298.8 MPa≤fu3 γmw⋅3=328.0 MPaf_e = \sqrt{f_a^2 + 3q^2} = 298.8\ \mathrm{MPa} \le \dfrac{f_u}{\sqrt{3}\,\gamma_{mw}} \cdot \sqrt{3} = 328.0\ \mathrm{MPa}
10.5.10.1.1
✓ OK · 91%InputsResults

Scope, assumptions and limitations

  • Stresses are assumed uniformly distributed along the effective weld length.
  • Maximum size on a square edge is t − 1.5 mm (cl. 10.5.8.3); on a rounded toe of a rolled section use 3/4 of the thickness.